Miranda DENSITE XVP-1801 Скачать руководство пользователя страница 17

Страница: 17 / 65

GUIDE TO INSTALLATION AND OPERATION

XVP-1801 |

If there is an error, the error status message appears in the message area without mouse-over.

•

If there are multiple errors, the error messages cycle so all can be seen

•

The icon whose status or error message is shown is highlighted with a mauve background

The table below lists the various status icons that can appear, and how they are to be interpreted.

•

In cases where there is more than one possible interpretation, read the error message in the iControl
window to see which applies.

Table –iControl Status Icon interpretation

Icon #1 – Manual Card Configuration

(green)

Remote card control activated. The iControl interface can be used to operate the card

(yellow)

Local card control active, The card is being controlled using the Densité frame control
panel, as described in section 3.3. Any changes made using the iControl interface will have
no effect on the card.

Icon #2 – Input 1 / Input 2 status

This icon reports the status of either input 1 or input 2, depending on Input 2 operating
mode (see Sect. 3.5.2) and situation

•

2x1 Switch – status of the input selected in the Input Select area of the input panel

•

Failover – usually status of input 1, but status of input 2 if input 1 has failed

•

Key/Fill – status of input 1

(green)

Signal detected and valid.

•

Beneath the icon, the format will be indicated as HD or SD, and the specific format
details will be listed if the cursor is moved over the icon.

(red)

Signal absent (Input 1 or Input 2 will be specified)

No rear

Reference mismatch

Video/TRS error

Input 2 selected in Failover mode

Icon #3 – Input 2 status – only if Input 2 is in the Key/Fill operating mode (see Sect. 3.5.2)

(green)

Signal detected and valid

Содержание DENSITE XVP-1801


































































Результаты поиска

Содержание DENSITE XVP-1801

Отзывы:

Miranda DENSITE XVP-1801, Руководство по установке и эксплуатации, Страница: 17 / 65

Результаты поиска

Содержание DENSITE XVP-1801

Отзывы: