Miranda ASD-211i/2D Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 23

Miranda ASD-211i/2D Скачать руководство пользователя страница 8

3

2 Installation

2.1 Unpacking

Make sure the following items have been shipped with your ASD-211i/2D. If any of
the following items are missing, contact your distributor or Miranda Technologies
Inc.

- ASD-211i/2D NTSC/PAL to 4:2:2 Adaptive Decoder

- ASD-211i/2D rear panel label

-

This

manual

2.2 ASD-211i/2D Mechanical Installation

The ASD-211i/2D must be mounted within Quartet, Quartet-C, Symphonie, or Solo

imaging

frames in order to provide power to the module. This section describes

how to install the ASD-211i/2D in any of these frames. It is not necessary to switch
off the power from these frames when installing or removing the ASD-211i/2D.

2.2.1 imaging Quartet and Quartet-C Frames

To install this module into Quartet or Quartet-C follow these steps. For a closer look
at module installation and removal, refer to the frame's

Guide to Installation and

Operation.

1. Remove the frame's front panel by rotating the thumb screws counterclockwise.

Pull on the handles.

2.   Select an empty slot.
3.   Carefully place the ASD-211i/2D between a set of module guides and gently
    push the module towards the rear of the frame until the module's edge

connector is secured to the backplane. Pull lightly on the module verifying that
it does not move.

4. Replace the frame's front panel. Make sure to rotate the thumb screws

clockwise in order to secure it to the chassis.

2.2.2 imaging Symphonie Frame

To install this module into Symphonie follow these steps. For a closer look at
module installation and removal, refer to the frame's Guide to Installation and
Operation.

1. Remove the front panel door by pulling on the door handles and gently lowering

it.

2. Select an empty compartment.
3. Carefully place the module between the module guides and slowly push the

module towards the rear of the frame until the module's edge connector is
secured to its rear module. A light pressure to mate the connectors may be
required. Pull lightly on the module verifying that it does not move.

4. Replace the front panel door.

«
...
6
7
8
9
10
...
»

Содержание ASD-211i/2D
























Отзывы:

Нет отзывов