Minuteman SCV 28/32 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 84

Minuteman SCV 28/32 Скачать руководство пользователя страница 25

25

CYLINDRICAL DECK SIDE SQUEEGEE COMPONENTS

A
B
C
D

Side Squeegee Blade
Black Squeegee Adjustment Knob (2)
Yellow Brush Access Knob
Side Squeegee Hinge

BRUSH CHANGES ON THE CYLINDRICAL DECK

In order to change the brushes on the cylindrical deck the side squeegee must be
moved in order to access the brush doors. The cylindrical deck was designed so one
can change the brushes without having to realign the side squeegees. This is
accomplished by removing the yellow three-sided knob (Item C) and swinging the
squeegee along the hinge bracket (Item D) located at the front of the deck, gaining
access to the brushes. Once completed inserting new brushes, replace the brush doors
and swing the squeegee back into place, tightening down the knob (Item C).

In order to remove or adjust the alignment of the side squeegees on the cylindrical
deck, remove the black three-sided knobs (Item B) and follow the instructions on the
previous page.

«
...
23
24
25
26
27
...
»

Содержание SCV 28/32





















































































Отзывы:

Нет отзывов