Minuteman SCV 28/32 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 84

Minuteman SCV 28/32 Скачать руководство пользователя страница 2

2

This manual is furnished with each new

MINUTEMAN SCV

TM

28/32

. This provides the

necessary operating and preventive maintenance instructions. Operators must read and
understand this manual before operating or servicing this machine.

This machine was designed to give you excellent performance and efficiency. For best
results and minimal cost, please follow the general guidelines below:

•

Operate the machine with reasonable care.

•

Follow the manufacturers suggested maintenance instructions as provided in this

booklet.

•

Use original Minuteman supplied parts.

TECHNICAL SPECIFICATIONS

Model

SCV

TM

28/32

Model No.

SCV28CQP / SCV28DQP / SCV32CQP / SCV32DQP

SCV28C / SCV28D / SCV32C / SCV32D / SCV28CPLUS

SCV28DPLUS / SCV32CPLUS / SCV32DPLUS

Current

60

Amps

Voltage, Batteries

36 volts, 6-6volt

Battery Capacity

275 Ah (Optional 395 Ah batteries available)

Sound Level

75 dB

Dimensions (LxWxH)

64” x 31” x 54” (163cm x 78.74cm x 137cm)

Gross Weight

1,243 lbs (564 kg) with batteries

847 lbs (384 kg) without batteries

Working Grade Transport

16% (10

°

)

Working Grade Cleaning

10% (7

°

)

Wheel to Floor Pressure

64 PSI Front, 69 PSI Rear

«
1
2
3
4
...
»

Содержание SCV 28/32





















































































Отзывы:

Нет отзывов