Minebea CC-Link CSD-892-73 Скачать руководство пользователя страница 91

Страница: 91 / 159

14-4. PLC memory explanation

A remote I/O (RX/RY : Bit handling register) and a remote register (RWw/RWr : Word

handling register) secures the zone in the master station depends on the occupied station

number. As shown in the table below in case of this unit.

Type

Occupied station number

Remarks

4 stations

occupied

2 stations

occupied

1 station

occupied

Remote input

128 points 64 points

32 points

I/O for each 16 points is

occupied as a system area.

Remote output

128 points 64 points

32 points

Remote

resister

Master

→

Remote

16 points

8 points

4 points

Remote

→

Master

16 points

8 points

4 points

The address number of the remote station allocated to the mastering station is as shown in

the table below.

Station

No.

Remote input

Remote

output

Remote register

Remarks

Master

→

Remote

→

Master

- - - - -

Specify the

master station

RX0000

RY0000

RWw0000

RWr0000

RX0020

RY0020

RWw0004

RWr0004

RX0040

RY0040

RWw0008

RWr0008

RX0120

RY0120

RWw00024

RWr0024

RX07E0

RY07E0

RWw00FC

RWr00FC

-Li

Содержание CC-Link CSD-892-73
































































































































































Результаты поиска

Содержание CC-Link CSD-892-73

Отзывы:

Minebea CC-Link CSD-892-73, Инструкция по эксплуатации, Страница: 91 / 159

Результаты поиска

Содержание CC-Link CSD-892-73

Отзывы: