Minebea CC-Link CSD-892-73 Скачать руководство пользователя страница 53

Страница: 53 / 159

tti

f F

6-10. Change of data stored place

The data stored place of [Internal RAM] or [EEPROM] is selected by C function CF-17.

Setting range

：

000

～

111

：

100

：

Internal RAM

：

EEPROM

* Each digit of the set value corresponds to the following items, and selects stored place of

each digit.

digit : ZERO set data,

digit : Tare weight cancellation data

digit : Set data of simple comparator mode and 5 steps comparator mode

Ex) Setting value

：

001 -> ZERO set data is stored at [EEPROM], and set data of tare weight

cancellation, simple comparator mode and 5 steps comparator mode is stored at [Internal

RAM]

6-11.Stability detection while setting

[VALID] or [INVALID] of stability detection while setting the S function and various

measurement mode is selected by C function CF-20.

Setting range

：

0,1

：

INVALID

：

VALID

6-12.Gravity acceleration compensation

When the calibration place and the using place of the measuring are different, the error is

caused in span by the difference of the gravity acceleration of the various place districts. The

gravity acceleration compensation function is a function for the compensation of this span

error by setting the gravity acceleration of two districts with a different calibration place and

using place. When the calibration place and the using place are the same, it is not necessary

to execute the gravity
acceleration compensation.

6-12-1. Setting method of gravity acceleration compensation

The setting method of the gravity acceleration compensation is selected by C function CF-

25.

Selectable range

：

0,1

：

The district number is set.

：

The numerical value of gravity acceleration is set.

•

Please refer to [12. Memorized place of set data] for the stored place of data other

than the above.

•

The data stored at [Internal RAM] is not backed up.

•

Please set the stored place to [Internal RAM] when the set data is continuously

changed, and the rewritable time of [EEPROM] might exceed about on million times.

•

Please do not change in the set value under the measurement because the A/D

sampling rate decreases temporarily while rewriting the set value when the stored

place of set data is [EEPROM]. Please set the stored place to [Internal RAM] if you

change the set value under the measurement.

Содержание CC-Link CSD-892-73
































































































































































Результаты поиска

Содержание CC-Link CSD-892-73

Отзывы:

Бренды по названию

Популярные бренды

Minebea CC-Link CSD-892-73, Инструкция по эксплуатации

Результаты поиска

Содержание CC-Link CSD-892-73

Отзывы:

Бренды по названию

Популярные бренды