Minebea CC-Link CSD-892-73 Скачать руководство пользователя страница 34

Страница: 34 / 159

tio

１

Push key when displays.

ZERO memorized, and displays.

* Set the condition that nothing is put on the measuring part.

ZERO Calibration by measurement value

Step

(Actual weight calibration)

to SPAN calibration

▲

to SPAN calibration

▲

ZERO calibration by numeric input

Step

(Electronic calibration)

１

Please set the load cell output value equal to ZERO in each

mV/V.

After setting, push key to display .

荷重をゼロにしたときに相当するロードセル出力値を入力して、ゼロ点を登録します。

mV/V

Set-up load

cell output value

Please select the method of ZERO calibration referring to [4-3. Selection of Calibration Method]

Change the value of digit to be changed.

CAL-S

Select the digit to be changed.

CAL-Z

* Memorized load cell output value is displayed.

By pushing key, displays, and by pushing

key, of condition display is turned on, and

mV/V

ZERO is registered by reading the load cell output value in the

condition that nothing is put on the measuring part (Initial condi-

tion including tare).

ZERO is registered by inputting the load cell output value when the
load is zero.
This procedure is used only when a specific condition is met.

sign lights on.

Push the key when blinks, and the

Please select the method of ZERO calibration referring to [4-3. Selection of Calibration Method]

displays.

ENTER

Memorized load

cell output value.

STABLE

CAL-Z

blinks for about 2 seconds when the output and input value of load cell exceeds over

ZERO adjustment range at minus side (at -2.5 mV/V or less).

blinks for about 2 seconds when the output and input value of load cell exceeds over

ZERO adjustment range at plus side (at 2.5 mV/V or more).

* Please con

ﬁ

rm the rated capacity and the tare amount, etc., so that ZERO should not

exceed the adjustable range.

Error display for ZERO calibration

Содержание CC-Link CSD-892-73
































































































































































Результаты поиска

Содержание CC-Link CSD-892-73

Отзывы:

Minebea CC-Link CSD-892-73, Инструкция по эксплуатации, Страница: 34 / 159

Результаты поиска

Содержание CC-Link CSD-892-73

Отзывы: