Minebea CC-Link CSD-892-73 Скачать руководство пользователя страница 29

Страница: 29 / 159

tio

▶

Continue from former page.

▶

ZERO calibration by the measurement value

ZERO calibration by numeric input

(Electric calibration)

SPAN calibration by the weight

SPAN calibration by numeric input

(

ZERO

)

(

Z MV

)

(

SPAN

)

(

S MV

)

ZERO is registered by reading the load

cell output value in the condition that

nothing is put on the weighing section.

(Initial condition including tare.)

Execute ZERO calibration by the numeric input.

Please adopt only under the specific condition

for this calibration method. Please refer to [4-3

Selection of calibration method] for the details.

SPAN is registered by inputting the value in

which the load cell output value of ZERO is

subtracted from the load cell output value

assumed when loaded for rating weight.

SPAN is registered by reading the load

cell output value in the condition to put

the weight set in step 6 on measuring

part.

When there is a weight.

When there is not a weight

Finish the calibration mode.

The set value is registered temporary until fixing by

pushing the [F/ENTER] key on display.

The set value is not saved when canceling on the

way.

Step

(Actual weight calibration)

Step

(Actual weight calibration)

(Electric calibration)

Finish the calibration

(

END

)

•

The environment used must execute the calibration again if necessary in altered

case.

•

When Minebea has executed the calibration in the combination with load cell, you

don't need to execute the calibration again.

•

Execute the calibration with actual load when you can prepare the weight of 2/3 or

more of weighing capacity. The accuracy over 1/1000 can be expected because of

a calibration in an actual measurement system.

•

SPAN calibration by the value input is possible even when there is no weight.

Содержание CC-Link CSD-892-73
































































































































































Результаты поиска

Содержание CC-Link CSD-892-73

Отзывы:

Minebea CC-Link CSD-892-73, Инструкция по эксплуатации, Страница: 29 / 159

Результаты поиска

Содержание CC-Link CSD-892-73

Отзывы: