manualshive.com logo in svg

Minebea Intec CAS1, Руководство по эксплуатации, Страница: 57 / 160

Поделиться
Скачать
Minebea Intec CAS1 Скачать руководство пользователя страница 57

5.6.7

Set preload

Setup information
-

Setting a preload for scales used in legal metrology is automatically carried out by the

power-on zero range. Explicit setting of the preload is not possible in legal

metrology.

After approx. 2 seconds, the prompt appears to place the irst linearization

weight on the scale.

5. Place the required weight on the scale.

After a short time, the diference between the measured value and the true

weight is displayed.

6. Accept the diference by pressing

(cancel by pressing

).

The prompt appears to place the second linearization weight on the scale.

7. Repeat the procedure for all required linearization weights.

After the inal linearization weight has been stored, a prompt appears asking you

to unload the load plate completely.

8. Remove the load from the load plate.

After a short time, the zero point is automatically adopted and the automatically

switches to weighing mode.

9. Close the locking switch again and, if necessary, reconigure the key

(press and

hold) to calibration/adjustment beforehand.

5 Getting started

Combics 1 Series Complete Scales Models CAW1P, CAW1S, CAS1

Minebea Intec

EN-55

Содержание CAS1

































































































































































Отзывы:

Нет отзывов