Mindray BeneFusion SP3 Скачать руководство пользователя

Страница: 45 / 80

4-9

Operation and Alarm Faults

Failure

Description

Possible Cause

Handling Method

Key failure

1.Poor contact between the

keypad board and the control

board.

2.The keypad board is faulty.

3.The control board is faulty.

1. Reconnect the keypad board

and the control board.

2. Replace the keypad board.

3. Replace the control board.

Buzzer sound

failure

1.Poor contact between the

keypad board and the control

board.

2.The control board is faulty.

3.The keypad board is faulty.

1.Reconnect the keypad board

and the control board.

2.Replace the control board.

3.Replace the keypad board.

Speaker sound

failure or hoarse

1.Poor contact of speaker

connection line.

2.Speaker assembly failure.

3.Speaker alarm circuit failure.

1.Reconnect the speaker.

2.Replace the speaker assembly.

3.Replace the control board.

Alarm lamp

failure

1. Poor contact between the

keypad board and the control

board.

2. The keypad board is faulty.

3. The control board is faulty.

1.Reconnect the keypad board

and the control board.

2.Replace the keypad board.

3.Replace the control board.

Monitoring Faults

Failure

Description

Possible Cause

Handling Method

The pressure

value remains

unchanged.

1.Poor connection or wire

damages exist in the link of

pressure sensor assembly -

pressure detection board - slider

adapter board - sensor adapter

board - control board.

2.The pressure sensor assembly

is faulty.

3.The pressure detection board

is faulty.

4.The control board is faulty.

1.Reconnect the link or replace the

wires.

2.Replace the pressure sensor

assembly.

3.Replace the pressure detection

board.

4.Replace the control board.

The pressure

value exceeds

the scale.

1.Poor connection or wire

damages exist in the link of

pressure sensor assembly -

pressure detection board - slider

adapter board - sensor adapter

board - control board.

2.The pressure sensor assembly

1.Reconnect the link or replace the

wires.

2.Replace the pressure sensor

assembly.

3.Replace the pressure detection

board.

4.Replace the control board.

Содержание BeneFusion SP3

















































































Результаты поиска

Содержание BeneFusion SP3

Отзывы:

Похожие инструкции для BeneFusion SP3

Бренды по названию

Популярные бренды

Mindray BeneFusion SP3, Руководство по обслуживанию

Результаты поиска

Содержание BeneFusion SP3

Отзывы:

Похожие инструкции для BeneFusion SP3

Бренды по названию

Популярные бренды