Mindray BeneFusion SP3 Скачать руководство пользователя

Страница: 22 / 80

2-10

2.3.2 Sensor Board

EEPROM

ADC

optical

coupler

I2C

GPIO

Slider

adapter

board

Sensor adapter board

Flexible

Printed

Circuit (FPC)

wire

Film

potentiometer

Rotary

potentiometer

Drive board

Pressure

sensor

Pressure

detection board

Block Diagram of Sensor Board

The sensor board consists of three small boards: a pressure detection board, a

slider adapter board, and a sensor adapter board. Wherein, the pressure sensor is

connected to the pressure detection board, and the signal is converted into a digital

signal by U2 acquisition. U5 is the calibration data of the pressure sensor stored in

EEPROM. U4 is the syringe in-position detection optical coupler. The signal of the

pressure detection board is sent to the monitoring CPU of the drive board after

being converted by the slider adapter board and the sensor adapter board.

The film potentiometer, which is attached to the sensor adapter board, is used to

detect the direction and speed of the motor, and the signal is forwarded to the

monitoring CPU of the drive board through the sensor adapter board. The rotary

potentiometer is used to detect the diameter of the syringe, and the signal is also

forwarded to the monitoring CPU of the drive board through the sensor adapter

board.

Key test points of the pressure detection board:

TP5 VDD 3.3V

TP3 Signal of the syringe in-position detection optical coupler.

TP8 I2C SCL signal for pressure detection

TP9 I2C SDA signal for pressure detection

Key test points of the sensor adapter board:

TP9 VDD 3.3V

TP7 Output signal of long potentiometer

TP4 Output signal of rotary potentiometer

Содержание BeneFusion SP3

















































































Результаты поиска

Содержание BeneFusion SP3

Отзывы:

Похожие инструкции для BeneFusion SP3

Бренды по названию

Популярные бренды

Mindray BeneFusion SP3, Руководство по обслуживанию

Результаты поиска

Содержание BeneFusion SP3

Отзывы:

Похожие инструкции для BeneFusion SP3

Бренды по названию

Популярные бренды