3-24
Chapter 3 Setup
Setting of Remote control
This section describes how to set up remote control using
Mimaki Remote Access.
See the online manual for Mimaki Remote Access.
When Mimaki Remote Access is in use, "During remote
control. [ent]" will appear on the display, and key
operations using the control panel of the unit will be
disabled.
If you press the [ENTER] key when "When remote control.
[Ent]" is displayed on the display, the remote control state
is released and you can operate the keys with the control
panel.
1
Press the
(MENU)
(>>)
key in LOCAL mode.
• MACHINE SETUP MENU will be displayed.
2
Press
to select “Remote
control”, and press the
key.
3
Press the
key at the
[Permit]screen.
4
Press
to
select “ENABLE”, and
“DESABLE”,and press the
key.
• ENABLE: Enables remote control by
MimakiRemote Access.
• DESABLE:Disables remote control by Mimaki
Remote Access.
• If you selected [DESABLE], press the [END/
POWER] key several times to exit.
5
Press the
key at the
[PIN code]screen.
6
Use the
to set the “PIN code”,
and press the
key.
• The PIN code is a 4-digit number used to
authenticate Mimaki Remote Access.
• Initial value: 0000
• Set Value
：
Set any 4 digits between 0000 and
9999.
7
Press the
key at the
[KeyLife]screen.
8
Use the
to set the “KeyLife” , and
press the
key.
• Key Life is used to set the amount of time that
Mimaki Remote Access will automatically
terminate remote control if there is no operation
during remote control.
• Set value: 5 to 120 (minutes)
9
Press the
key several times to
end the setting.
Setting a LANGUAGE
You can change the displayed language.
1
Press the
(MENU)
(>>)
key local mode.
2
Press
to select “LANGUAGE”,
and press the
key.
3
Press
to select language, and
press the
key.
•
Set Value
：日本語
/ English / Deutsch / Español
/ Italiano /
中文
/ Turkish
4
Press the
key several times to
end the setting.
Setting a Ionizer (Option)
When the optional ionizer is connected, select "ON" to
remove static electricity.
For safety instructions and precautions, refer to the
“Instruction Manual for Ionizer” for UJF-3042MkII/
6042MkII.
1
Press the
(MENU)
(>>) key
in LOCAL mode.
2
Press
to select “MACHINE
SETUP”, and press the
key.
• MACHINE SETUP MENU will be displayed.
3
Press
to select “Ionizer”, and
press the
key.
• The setting of "Ionizer" is selected.
4
Press
to select set value, and
press the
key.
• If you select "ON," the device moves the table in
order to remove static electricity from all the
printing surfaces according to the printing data
before the printing operation starts.
5
Press the
key several times to
end the setting.
Connecting from Mimaki Remote Access.
On the PIN code input screen, enter the 4-digit
number according to the PIN code value set in the
main unit to authenticate.
• If the set value is "0000", any 4-digit number (any
combination of numbers except "0000" is
acceptable)
• If the set value is not "0000", the 4-digit number
is the same as the set value.
• Please note that if the PIN code is "0000", any
number can be used for authentication.
• Displayed only when the Ionizer option is enabled.
Содержание 3042 MkII EX
