Milltronics OCM II PL-269 Скачать руководство пользователя страница 102

Страница: 102 / 107

TRANSDUCER MOUNTING - OCM II APPLICATIONS

Bracket

flexible conduit

* 1" NPT PVC

coupling

steel channel

ST-25

transducer

Flexible conduit mounted transducer should not be

subjected to wind, vibration or jarring.

Flexible Conduit

* 1" NPT PVC nipple

Blind Flange

Plywood

* 1" NPT

PVC coupling

Plywood mounting provides

excellent isolation, but must be rigid

enough to avoid flexing if subjected

to loading.

Flange, gasket and hardware supplied by customer.

Refer to Figure 7.

Guidelines:

1. Do not mount transducer directly to metal. Use PVC coupling and nipple as provided.

2. Do not overtighten mounting. Hand tightening PVC coupling and nipple is sufficient.

3. In OCM II applications, transducer mount (flange, bracket, conduit or plywood) must keep

transducer perpendicular to liquid surface.

4. Transducer installation, whether in non-hazardous (as shown) or hazardous areas, must be done

in conjunction with approved conduit, boxes and fittings and to procedures in accordance with all
governing regulations.

5. Inner standpipe surface and ends must be smooth and free of burrs, ridges or seams.

FIG. 5

PL-269

10 – 6

Содержание OCM II PL-269












































































































Результаты поиска

Содержание OCM II PL-269

Отзывы:

Бренды по названию

Популярные бренды

Milltronics OCM II PL-269, Инструкция по эксплуатации

Результаты поиска

Содержание OCM II PL-269

Отзывы:

Бренды по названию

Популярные бренды