MillRight CARVE KING 2 Скачать руководство пользователя | Manualshive

Страница: 1 / 34

background image

Page 1 or 34

ASSEMBLY INSTRUCTIONS FOR THE MILLRIGHT CNC CARVE KING 2

Version 1.00

Note that these are instructions for the Carve King 2. For instructions on the original Carve King, see

www.millrightcnc.com/resources

Contact

[email protected]

if you have questions.

Important safety rules for operating your MillRight CNC Carve King 2:
Never place your hands near a spinning end mill or bit.
Unplug the router before changing cutting tools.
Always wear eye and ear protection while operating your machine.
Always run a dust collector or wear a mask while performing a milling operation.
Do not leave the machine unattended while running a milling operation.
Do not operate your machine while under the influence of alcohol or drugs.
Secure long hair and loose clothing so it is not caught in spinning mechanisms.
Ensure work pieces are properly secured before running a milling operation.
Keep a fire extinguisher nearby.
Visually inspect wires prior to power up to prevent short circuits.

Note:

We recommend using a blue thread locker on any fastener not secured with a lock washer or lock nut.

1
2
3
...
»

Содержание CARVE KING 2



































Отзывы:

Нет отзывов

Похожие инструкции для CARVE KING 2

Бренд: ABB Страницы: 138

Бренд: ABB Страницы: 116

Relion 615 series

Бренд: ABB Страницы: 136

Бренд: Saito Страницы: 90

Бренд: Vancare Страницы: 31

Бренд: Zetkama Страницы: 6

Бренд: Facility Explorer Страницы: 4

Бренд: ZETRON Страницы: 3

Бренд: GAUGEMASTER Страницы: 2

Бренд: EasyIO Страницы: 19

Бренд: Zero 88 Страницы: 2

Бренд: Zenit Страницы: 24

Бренд: Magnescale Страницы: 3

Бренд: Omega Страницы: 56

Бренд: Omega Страницы: 2

Бренд: Omega Lift Страницы: 24

Бренд: Omega Lift Страницы: 8

Бренд: OMA Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды