Miele Honeycomb care Paragon sensor Скачать руководство пользователя | Manualshive

Страница: 39 / 56

background image

Levelling the tumble dryer

The appliance must be perfectly level
to ensure safe and proper operation.

^

The screw feet can be adjusted to
compensate for any unevenness in
the floor.

,

The air inlet and outlet vents on

the front of the tumble dryer must
not be covered as this would
prevent sufficient ventilation for
cooling the condenser unit.

Room in which the dryer is located

Air taken in for use in the drying
process will be warm when it is
expelled from the front of the dryer. This
expelled air heats up the air in the
room. It is therefore very important to
ensure that the room is adequately
ventilated, particularly if the dryer is
located in a small room. Otherwise
running times and energy consumption
could be increased.

Washer-dryer stack

The tumble dryer can also be
combined with a Miele washing
machine in a washer-dryer stack. The
appropriate "WTV" stacking kit
(available to order) to match your dryer
is required.

,

Stacking kits must only be

installed by a suitably qualified fitter.

Before moving the tumble dryer
again (e.g. when moving house)

After each use a small quantity of
condensed water will collect in the area
around the pump. This water can run
out if the tumble dryer is tipped up
when it is being moved. It is a good
idea to run the

Cool air

programme for

approximately 1 minute before moving
the tumble dryer. Any remaining
condensed water will then be fed into
the condensed water container or out
through the drain hose.

Installation

39

«
...
37
38
39
40
41
...
»

Содержание Honeycomb care Paragon sensor

























































Отзывы:

Нет отзывов

Похожие инструкции для Honeycomb care Paragon sensor

Бренд: JAP Страницы: 68

Pearl Dryer AC5011

Бренд: Remington Страницы: 68

FAMILY PRO ACCESS

Бренд: TEFAL Страницы: 15

Бренд: smith+nobel Страницы: 12

MF200D80WB Series

Бренд: Midea Страницы: 44

Бренд: Morphy Richards Страницы: 6

Бренд: Gardner Denver Страницы: 16

Бренд: Maguire Products Страницы: 39

Ultimate EZ Clean

Бренд: T-Fal Страницы: 23

Бренд: Electrolux Страницы: 40

Бренд: Electrolux Страницы: 24

Бренд: Electrolux Страницы: 44

Бренд: Electrolux Страницы: 36

Бренд: Electrolux Страницы: 44

Бренд: Electrolux Страницы: 48

Бренд: Electrolux Страницы: 52

Бренд: Electrolux Страницы: 52

Бренд: Electrolux Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды