Miele Honeycomb care Paragon sensor страница 21 Скачать руководство пользователя

Страница: 21 / 56

The system lock prevents your
machine being used without your
knowledge.

It can be activated if wished.

The dryer's electronics are locked. The
dryer can still be switched on but a
programme cannot be started. The

Locked

indicator light will flash if an

attempt is made to start a programme.

The door is not locked and can be
opened at any time.

To activate the lock

Before you begin, first ensure that:

– The tumble dryer is switched off.

– The door is closed.

Press the

Anti-crease

and

Drying

level

buttons at the same time and

hold them pressed in until you reach
step

below.

Press the

I-On/0-Off button in.

Wait until the indicator light for the

Start/Stop

button starts flashing ...

... and then press the

Low

temperature/Short/Cool air

button

three times.

Then release the

Anti-crease

and

Drying level

buttons.

The

Locked

indicator light will flash.

The electronics have now been locked.

Switch the dryer off with the

I-On /

0-Off

button.

To deactivate the lock

Before you begin, first ensure that:

– The tumble dryer is switched off.

– The door is closed.

Press the

Anti-crease

and

Drying

level

buttons at the same time and

hold them pressed in until you reach
step

below.

Press in the

I-On/0-Off button.

Wait until the indicator light for the

Start/Stop

button starts flashing ...

... and then press the

Low

temperature/Short/Cool air

button

three times.

Then release the

Anti-crease

and

Drying level

buttons.

The

Locked

indicator light will go out.

The electronics are no longer locked.

You can now use the dryer or switch

it off with the

I-On/0-Off

button.

Electronic system lock

Содержание Honeycomb care Paragon sensor

























































Результаты поиска

Содержание Honeycomb care Paragon sensor

Отзывы:

Похожие инструкции для Honeycomb care Paragon sensor

Бренды по названию

Популярные бренды

Miele Honeycomb care Paragon sensor, Руководство по эксплуатации

Результаты поиска

Содержание Honeycomb care Paragon sensor

Отзывы:

Похожие инструкции для Honeycomb care Paragon sensor

Бренды по названию

Популярные бренды