Miele Honeycomb care Paragon sensor Скачать руководство пользователя | Manualshive

Страница: 44 / 56

background image

Programme

Load

Final spin speed

in a domestic washing machine

Energy Duration

kg*

rpm

kWh

Minutes

Cottons Normal

6.0

1000 (60 % residual moisture)**

1200
1400
1600
1800

3.30
3.00
2.85
2.55
2.50

89
81
78
70
69

Cottons Hand iron

rr

6,0

1000 (60 % residual moisture)**

1200
1400
1600
1800

2.65
2.35
2.20
1.85
1.80

71
63
60
52
51

Minimum iron/Delicates Normal

3.0

1200 (40 % residual moisture)**

1.20

37

Minimum iron/Delicates Hand iron

3.0

1200

1.00

32

Automatic Normal

r

3.5

800

2.10

85

Shirts Normal

2.0

600

1.15

41

Denim Normal

3.0

900

2.00

96

Woollens handcare

2.0

1000

0.15

4

Smoothing

3.0

1000

0.30

8

*

Weight of dry laundry

** EN 61121:2005 test programme
All data without a "star" against it was calculated using EN 61121:2005.
Before testing in accordance with EN 61121, dry a 3 kg load of cotton laundry with 70% residual
moisture as per the above standard using the Cottons Normal programme without any extra options.

Consumption data can vary from the nominal values given above depending on the size of the
load, types of textiles, residual moisture levels after spinning, fluctuations in the electricity
supply and any extra options selected.

Consumption data

44

«
...
42
43
44
45
46
...
»

Содержание Honeycomb care Paragon sensor

























































Отзывы:

Нет отзывов

Похожие инструкции для Honeycomb care Paragon sensor

Бренд: Conair Страницы: 8

FriFri Frita+ 6

Бренд: Middleby Страницы: 20

Бренд: U.S. Range Страницы: 20

Бренд: Braun Страницы: 4

DOMINATORPLUS E3865

Бренд: Falcon Страницы: 10

DNH D8513AX-AUS

Бренд: Hoover Страницы: 15

Бренд: Remington Страницы: 9

Бренд: nedis Страницы: 44

AF 5500 Crunchy

Бренд: ECG Страницы: 84

Бренд: GoWISE USA Страницы: 16

Бренд: ORIGO Страницы: 2

Бренд: Indesit Страницы: 20

Бренд: Farouk Страницы: 28

Бренд: Haier Страницы: 12

Бренд: Haier Страницы: 17

Бренд: Haier Страницы: 22

Бренд: Haier Страницы: 16

Бренд: Haier Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды