Miele Honeycomb care Paragon sensor Скачать руководство пользователя

Страница: 49 / 56

Memory function

The electronics will memorise the
drying level and any extra options
selected for the current drying
programme.

The Memory function

– is activated when the machine is

delivered. You can deactivate it if
wished.

– does not work if a programme is

cancelled or if Delay start has been
selected.

Follow steps

to programme and

store in memory.

Before you begin, first ensure that:

– The tumble dryer is switched off.

– The door is closed.

Press the

Start/Stop

button and keep

it pressed in whilst carrying out steps

Press the

I-On/0-Off

button in.

Wait until the indicator light for the

Start/Stop

button lights up constantly . . .

. . . and then release the

Start/Stop

button.

Press the

Buzzer

button twice.

– The

Buzzer

indicator light will briefly

flash on and off six times.

–

and

(default setting) will flash

alternately in the display.

The number which appears alternately
in the display with

means:

Memory activated

(the

Drying

indicator light will also

flash)

Memory deactivated

Pressing the

Start/Stop

button

switches from one to the other.

Switch the machine off with the

I-On/0-Off

button.

The setting you have selected is now
stored in memory. You can change it
again at any time.

Programmable functions

Содержание Honeycomb care Paragon sensor

























































Результаты поиска

Содержание Honeycomb care Paragon sensor

Отзывы:

Похожие инструкции для Honeycomb care Paragon sensor

Бренды по названию

Популярные бренды

Miele Honeycomb care Paragon sensor, Руководство по эксплуатации

Результаты поиска

Содержание Honeycomb care Paragon sensor

Отзывы:

Похожие инструкции для Honeycomb care Paragon sensor

Бренды по названию

Популярные бренды