Miele Honeycomb care Paragon sensor Скачать руководство пользователя | Manualshive

Страница: 36 / 56

background image

In the event of any faults which you
cannot remedy yourself, please contact

– your Miele dealer or

– the Miele Service Department (see

back cover for contact details).

When contacting your dealer or the
Service Department, please quote the
model and serial number of your
appliance, both of which are shown on
the data plate situated on the right
hand side below the drum aperture.

N.B. A call-out charge will be
applied for unnecessary service
visits where the problem could have
been rectified as described in this
instruction manual.

Future updates (PC)

The indicator or check light marked

PC

on the fascia panel is the interface used
by the Miele service technicians during
service work for testing purposes and
for updating the appliance's
programme data.

Appliance guarantee

Please see the guarantee card
supplied with your appliance.

Optional accessories

Optional accessories for this dryer are
available from your Miele Dealer, the
Miele Spare Parts Department or via the
internet at www.miele-shop.com.

Please note that telephone calls may
be monitored and recorded for
training purposes.

After Sales service

36

«
...
34
35
36
37
38
...
»

Содержание Honeycomb care Paragon sensor

























































Отзывы:

Нет отзывов

Похожие инструкции для Honeycomb care Paragon sensor

Бренд: HAEGER Страницы: 24

Бренд: Saivod Страницы: 35

Бренд: Hotpoint Страницы: 16

Бренд: Supra Страницы: 24

da Benedetta NNE000024NOC

Бренд: Kasanova Страницы: 50

Бренд: Frigidaire Страницы: 6

Бренд: Black & Decker Страницы: 21

Бренд: Black & Decker Страницы: 20

Бренд: Black & Decker Страницы: 28

Бренд: LG Страницы: 43

Бренд: LG Страницы: 2

Бренд: LG Страницы: 2

Бренд: LG Страницы: 52

Бренд: LG Страницы: 2

Бренд: LG Страницы: 77

Бренд: LG Страницы: 48

FWV696 SE Series

Бренд: LG Страницы: 56

Бренд: LG Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды