Miele HG07-W страница 99 Скачать руководство пользователя

Страница: 99 / 124

Problem solving guide

Water inlet fault

Issue

Cause and remedy

The warning buzzer is
sounding.
One of the following
messages appears in
the display:



Open stopcock

The stopcock is closed.



Open the stopcock fully.



Water intake

Before rectifying the problem:



Switch the dishwasher off.

The water inlet is restricted.



Open the stopcock fully and start the programme
again.



Clean the filter in the water inlet (see “Cleaning
and care” – Cleaning the filter in the water inlet”).



The water-connection pressure is lower than
50 kPa.
Seek professional advice.



The on-site connection for the water drainage may
be too low and you will need to vent the water
drainage (see “Installation – Water drainage”).



Fault F18

A technical fault has occurred.



Switch the dishwasher off.



Close the stopcock.



Call the Miele Customer Service Department.

The following fault
message appears on
the display during the

SolarSave

programme:

Intake temperature too low

The intake water has not reached the required
temperature of 45 °C (see “Installation – Water inlet”).



Start the programme again.



If the fault message appears again, select a
different programme.

Содержание HG07-W





























































































































Результаты поиска

Содержание HG07-W

Отзывы:

Похожие инструкции для HG07-W

Бренды по названию

Популярные бренды

Miele HG07-W, Руководство по эксплуатации

Результаты поиска

Содержание HG07-W

Отзывы:

Похожие инструкции для HG07-W

Бренды по названию

Популярные бренды