background image

Installation

*INSTALLATION*

118

Electrical connection

Electrical connection

The appliance is supplied with a mains
cable with moulded plug for
connection. Please ensure the
connection data (voltage and
frequency) quoted on the data plate
match the household mains supply.
Please consult a qualified electrician if
you are in any doubt.

Connection should be made via a
suitable switched socket which is easily
accessible after installation.

For extra safety it is advisable to
operate the appliance via a suitable
residual current device (RCD). Contact
a qualified electrician for advice.

Do not connect the appliance to the
mains electricity supply by a
multisocket adapter or an extension
lead. These are a fire hazard and do not
guarantee the required safety of the
appliance.

If the connection cable is faulty, it may
only be replaced by a qualified
electrician in order to avoid a hazard.

Non-rewireable plugs BS 1363

The fuse cover must be refitted when
changing the fuse, and if the fuse cover
is lost, the plug must not be used until a
suitable replacement is obtained. The
colour of the correct replacement cover
is that of the coloured insert in the base
of the plug, or the colour that is
embossed in words on the base of the
plug (as applicable to the design of plug
fitted).

Replacement fuses must be ASTA
approved to BS 1362 and have the
correct rating. Replacement fuses and
fuse covers may be purchased from
your local electrical supplier.

WARNING: THIS APPLIANCE MUST
BE EARTHED

Содержание HG07-W





























































































































Отзывы: