Miele HG07-W страница 96 Скачать руководство пользователя

Страница: 96 / 124

Problem solving guide

Many malfunctions and faults that can occur in daily operation can be easily
remedied. Time and money will be saved because a service call will not be
needed.

The following guide may help you to find the reason for a malfunction or a fault,
and to correct it.

This section only lists faults that you can remedy yourself. All other faults are
shown in



Fault FXX

Technical problems

Issue

Cause and remedy

The display remains
dark after the
dishwasher has been
switched on with the



sensor control.

The dishwasher is not plugged in.



Insert the plug and switch on at the socket.

The mains fuse has tripped.



Reset the trip switch in the fuse box or replace the
fuse in the plug (see data plate for minimum fuse
rating).



If the mains fuse trips again, contact the Miele
Customer Service Department.

The dishwasher stops
during a programme.

The mains fuse has tripped.



Reset the trip switch in the fuse box or replace the
fuse in the plug (see data plate for minimum fuse
rating).



If the mains fuse trips again, contact your Miele
dealer.

Содержание HG07-W





























































































































Результаты поиска

Содержание HG07-W

Отзывы:

Похожие инструкции для HG07-W

Бренды по названию

Популярные бренды

Miele HG07-W, Руководство по эксплуатации

Результаты поиска

Содержание HG07-W

Отзывы:

Похожие инструкции для HG07-W

Бренды по названию

Популярные бренды