Miele G 7881 Скачать руководство пользователя | Manualshive

Страница: 9 / 76

background image

Accessories

~

Whatever the application, only Miele

accessories should be connected to
this machine. Consult a Miele
Application Specialist for details on the
type of equipment to use.

~

Only Miele mobile units, baskets

and inserts should be used. If Miele
accessories are altered in any way, or
equipment from another manufacturer
is used, Miele cannot ensure the
cleaning and disinfection results.
Damage or injury caused in this way
are excluded from the warranty.

~

Only use processing chemicals that

are approved by their manufacturer for
the application involved. Any negative
effects on items and the machine itself
are the liability of the manufacturer of
the processing chemicals.

Symbols on the appliance

Caution:
Comply with the Operating
Instructions!

Caution:
Danger of electric shock!

Disposing of your old appliance

~

Old appliances may be

contaminated from exposure to blood
or other body fluids and must therefore
be decontaminated before disposal.
For safety and environmental
protection, be sure to drain/remove all
processing chemical residue. (Comply
with safety regulations and wear
protective eyewear and gloves.)
Remove or destroy the door latch, to
prevent children from locking
themselves inside. The appliance can
now be sent for disposal through the
proper resource recovery facilities.

The manufacturer will not be held
liable for damage caused by failure
to comply with the safety instructions
and warnings.

Safety instructions and warnings

9

«
...
7
8
9
10
11
...
»

Содержание G 7881













































































Отзывы:

Нет отзывов

Похожие инструкции для G 7881

Бренд: Laica Страницы: 4

Infield Rascal Pro

Бренд: ABI Attachments Страницы: 8

Бренд: Abicor Binzel Страницы: 84

Бренд: ABI Attachments Страницы: 5

Бренд: abem Страницы: 47

Бренд: Abely Страницы: 5

Бренд: Federal Страницы: 43

Бренд: Danfoss Страницы: 106

Growers Supply 109722

Бренд: FarmTek Страницы: 9

Бренд: Rane Страницы: 38

Бренд: Kartsana Страницы: 36

Бренд: MagCore Страницы: 80

Бренд: MagCore Страницы: 80

Бренд: Mangar International Страницы: 8

Бренд: Malvern Instruments Страницы: 30

Бренд: zarges Страницы: 36

Бренд: Garden Treasures Страницы: 2

Бренд: Phenix Technologies Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды