Miele G 670 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 68

background image

Caring for the environment

Disposal of the packing material

The transport and protective packing
has been selected from materials
which are environmentally friendly for
disposal and can normally be recycled.

Rather than just throwing these
materials away, please ensure they are
offered for recycling.

Disposal of your old machine

Old machines contain materials which
can be re-cycled. Please contact your
local authorities or scrap merchant
about potential recycling schemes, be-
fore disposing of the appliance.

Energy saving washing

These dishwashers are exceptionally ef-
ficient in their use of water and elec-
tricity. You can make the most of your
appliance by following these tips:

If your household water system is
suitable , this dishwasher can be
connected to a hot water supply up
to 60 °C for further economies.
However, if your water is heated by
electricity we would still recommend
connection to cold water.
In the UNIVERSAL 55° programme,
depending on the capacity of the
dishwasher, when connected to hot
water 55°C up to 0.7 kWh of electri-
cal energy is saved. The hot water
provides this energy, and the ap-
prox. 0.13 l oil or 0.14 m

3

natural gas

needed to heat the water is consider-
ably more cost effective.
Although all stages of the wash then
take place with hot water, savings
are made in cost, time and energy.

Make full use of the baskets without
overloading the dishwasher for most
economical washing.

Choose the programme to suit the
type of crockery being washed and
the degree of soiling.

If baskets are only half full use the
ECONOMY programme.

Use the correct dosages of deter-
gent.

Caring for the environment

9

«
...
7
8
9
10
11
...
»

Содержание G 670





































































Отзывы:

Нет отзывов

Похожие инструкции для G 670

Бренд: Panasonic Страницы: 44

Бренд: Fagor Страницы: 22

Бренд: Jackson Страницы: 2

Бренд: Jackson Страницы: 2

Бренд: Jackson Страницы: 2

Glasswashers Delta 5

Бренд: Jackson Страницы: 2

Бренд: GE Страницы: 16

Бренд: Hyundai power products Страницы: 36

Бренд: Fagor Страницы: 112

Бренд: Estate Страницы: 1

Бренд: GE Страницы: 60

Бренд: Asko Страницы: 36

Бренд: VALBERG Страницы: 92

Бренд: Hotpoint Страницы: 16

Бренд: Hoonved Страницы: 21

Бренд: Halcyon Страницы: 6

Бренд: Hanseatic Страницы: 84

Бренд: Zanussi Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды