Miele G 670 Скачать руководство пользователя страница 41

Страница: 41 / 68

Problem solving guide

With the aid of the following explana-
tory notes, minor faults can be cor-
rected without contacting the Miele Ser-
vice Department.

Any work on the electrical compo-
nents of the appliance should only
be carried out by a suitably quali-
fied and competent person in ac-
cordance with local and national
regulations. Unauthorised repairs
could be dangerous.

Faults/possible causes

The dishwasher does not start

– The door is not properly closed.

– The plug is not properly inserted.

– The fuse is defective/has blown.

The dishes are not clean

– The dishes are incorrectly loaded.

– The wrong amount of detergent was

used.

– The stopcock was not fully opened.

– The water pressure is too low (too

little water in the wash cabinet) – see
chapter “Checking the water level”.

– The filter in the water inlet screw con-

nection is blocked - see “Cleaning
and care”.

– The filters in the wash cabinet are

not clean - see “Cleaning and care”.

– Spray arm jets are blocked - see

“Cleaning and care”.

– The spray arms are obstructed by

items in the baskets.

– The opening in the middle of the cut-

lery tray is blocked by a piece of cut-
lery. Not enough water flows through
the middle spray arm.

White residue on cutlery and
crockery

– Not enough rinse aid.

– No salt in the salt reservoir.

– Salt reservoir lid has not been

screwed on properly.

Water in the wash cabinet at the end
of a programme

– The drain hose is kinked.

– The drain pump or non-return valve

may be blocked. See “Cleaning and
care”.

After Sales Service

Should you still have any difficulties,
or if the appliance is under guaran-
tee please contact:

– your Miele Dealer or

– the Miele Service Department

See back cover for addresses.

Please quote the model type and
number of your appliance. This infor-
mation can be found on the data
plate inside the door.

Problem solving guide

Содержание G 670





































































Результаты поиска

Содержание G 670

Отзывы:

Похожие инструкции для G 670

Бренды по названию

Популярные бренды

Miele G 670, Руководство по эксплуатации

Результаты поиска

Содержание G 670

Отзывы:

Похожие инструкции для G 670

Бренды по названию

Популярные бренды