Miele G 670 Скачать руководство пользователя страница 55

Страница: 55 / 68

Installation integrated “i“ Dishwashers

3. Fitting the facia panel

The facia panel is delivered separately
in the colour ordered with the necess-
ary accessories.
It has to be fitted to the dishwasher
when it is being installed.

Place the seal supplied

into the

groove surrounding the ventilation
grille

Push the ventilation grille

into posi-

tion.

Attach caps

to the push button

switches.

Place the facia panel

in position

and screw into place from the inside
using the six screws

Attach the switch knob

Only applicable when using the GDU
decor set

(to convert an "i" version to a

built-under "U" version)

If the GDU decor set is being used, the
adapter strips

must first of all be

removed, and stored for possible use
in the future. See also the separate in-
structions for fitting the GDU decor set.

Press out the adapter strips from the
fitting slits in the facia panel.

Installing integrated “i” Dishwashers

Содержание G 670





































































Результаты поиска

Содержание G 670

Отзывы:

Похожие инструкции для G 670

Бренды по названию

Популярные бренды

Miele G 670, Руководство по эксплуатации

Результаты поиска

Содержание G 670

Отзывы:

Похожие инструкции для G 670

Бренды по названию

Популярные бренды