Miele G 670 Скачать руководство пользователя страница 60

Страница: 60 / 68

6. Adjusting the door springs

The door springs are correctly adjusted
when a half opened door (approx. 45 °
opening angle) remains in that position
when released.

If the door drops down, then the door
springs need to be tightened.

If, however, it rises up, then the springs
need to be released.

The adjusting screw is located in the
upper front strip at the left hand side of
the dishwasher.

Open the dishwasher door.

Adjust the door spring until it is cor-
rectly balanced:
– turn clockwise = tighten
– turn anti-clockwise = loosen.

Push the dishwasher back into its re-
cess.

7. Level and secure the

dishwasher

To ensure the stability of the dish-
washer it must be screwed to the con-
tinuous worktop after it has been posi-
tioned.

Half open the dishwasher door.

Screw one of the 4 x 15 screws sup-
plied from below into the holes in the
right and left hand side of the upper
strip.

Do not lift the dishwasher to do this.
If necessary, screw the feet out fur-
ther.

Installation integrated “i” Dishwashers

Содержание G 670





































































Результаты поиска

Содержание G 670

Отзывы:

Похожие инструкции для G 670

Бренды по названию

Популярные бренды

Miele G 670, Руководство по эксплуатации

Результаты поиска

Содержание G 670

Отзывы:

Похожие инструкции для G 670

Бренды по названию

Популярные бренды