Miele G 670 Скачать руководство пользователя страница 61

Страница: 61 / 68

If one of the screw positions is in the
cut-out area, e.g. of the built-in sink, at-
tach the fixing bracket supplied.

Pull the dishwasher approx. 5-10 cm
out of the recess.

Position the fixing bracket.

Push the dishwasher back into the re-
cess, adjust and screw into position
with a (3.9 x 22) screw.

For “Corian” or granite worktops there
is a special accessory to fix the dish-
washer to an adjacent kitchen unit.

Pull the dishwasher approx. 5-10 cm
out of its niche.

Fit the lug of each fixing bracket into
the guide hole on top of the dish-
washer, and then swing to the left or
right side respectively.

Push the dishwasher back into the
niche, align, and fix to the adjacent
kitchen unit(s) with 2 screws (3.5 x 15)
for each bracket.

Installation integrated “i” Dishwashers

Содержание G 670





































































Результаты поиска

Содержание G 670

Отзывы:

Похожие инструкции для G 670

Бренды по названию

Популярные бренды

Miele G 670, Руководство по эксплуатации

Результаты поиска

Содержание G 670

Отзывы:

Похожие инструкции для G 670

Бренды по названию

Популярные бренды