Midas HERITAGE 4000, Руководство оператора

Страница: 42 / 78

MIDAS XL031
monitor
add mode
SOLO
pre fade
(pfl)
10
10
5
5
0
20
30
40
dB
10
10
5
5
0
20
30
40
dB
mute mute
solo clear
SOLO
Monitor Module Monitor Module
Mute (left)
Mute (right)
Solo (add mode)
Solo (pre fade PFL)
Solo Clear
Fader
- toggles the mute on the left hand side of the local monitor outputs.
- toggles the mute on the right hand side of the local monitor outputs.
- The solo add mode switch changes the behaviour of the consoles solo
operation. See the panel below for detailed information)
- The solo PFL switch sends the mono PFL bus signals to the headphones
and local monitor outputs in place of the stereo AFL solo buss signals.
- The solo clear button has two functions:-
1 - The solo clear button will light to indicate that a solo is in place on the console.
2 - Pressing the solo clear button while lit will clear any active solos on the desk.
- The monitor fader allows continuous adjustment of all three local monitor output
signals from off (-inf) to +10dB.
Normal Solo Function
Solo Add Mode
Solo Clear
When a channel solo is activated, the signal is sent to the PFL mono and the AFL stereo busses.
If the switch is pressed for a short time, it will latch the solo on or off. The solo system is, by default, auto
cancelling. This means that when a solo is pressed, any previous solos will be released. However, if a number of
solos are pressed within a short period (i.e. almost at the same time) of each other, a number of solos can be
operated simultaneously.
If a solo switch is pressed for more than one second, the solo latch is disabled and the solo is cancelled as soon as
the solo switch is released.
When in solo add mode (solo add mode switch on the monitor module) the auto cancelling solo function is disabled
allowing multiple solos to be activated. There is a priority order for the solo system in this mode which is:-
(High) Input Solos
VCA Solos
(Low) Direct In Solos
Group Solos
Output Solos
In the case of a high priority solo being placed after lower priority solo, the higher priority solo will be sent to the
PFL and AFL busses and the lower priority solo will not. Once the higher priority solo is removed, the lower priority
solo will then be sent to the AFL and PFL busses.
The Solo Clear switch on the monitor module will illuminate to show that a solo is in place on the console.
Pressing the Solo Clear switch on the monitor module will release all active solos on the console.
Solo Behaviour Solo Behaviour
monitor
modul
e
MIDAS XL031
+21+
+18+
+15+
+12+
+9+
+6+
+3+
0
-3-
-6-
-9-
-12-
-15-
-18-
-21-
-24-
-27-
-30-
-33-
-36-
monitor
add mode
phones
0
+10
MUTE
SOLO
SOLO
level
masters
input
level
pre fade
(pfl)
TALK
to all
internal
PRE
meter
change
over
10
10
5
5
0
20
30
40
dB
10
10
5
5
0
20
30
40
dB
mute mute
solo clear
PAD ON
R L
l-r reverse
left only
-20dB
sum
O MONO
output ‘b’
output ‘b’
mono output
mono source
TALK
SOLO
MONO
SOLO
MONO
ST
C/O
C/O
EXT
stereo output
stereo source
0
+10
0
+10
mute
100
1k
freq
10k
level
0
1kHz
PINK
generator
internal
generator
external
signal
generator
+10
300
level
mic gain
talk mic
talk
internal
talk
external
+10 +20 +60
+40 0
Operators Manual
- Page 37