Microplex logiJET TM4 Скачать руководство пользователя страница 109

Страница: 109 / 149

Panel Functions 109

_______________________________________________________________________________________________

MICROPLEX

Operator’s Manual logiJET TM4

Edition 1.2p

8.3.17. Data Interface Configuration

This function is used to set the interface parameters.

Panel display

Notes

[Online ]

Turn the printer OFF LINE with this key.

[Menu Level 1 ]

. . .

Press the

key until

[Configuration

] is displayed.

[Configuration ]

Press this key. This selects the Configuration
menu.

[Interface ]

Press this key. This selects the Interface menu.

[SIA Timeout ]

Press this key. This selects the Timeout menu.

[ 30 s ]

The currently set value for the timeout is
displayed (here: 30 seconds).

. . .

Pressing the

key changes

the timeout value.

[ 40 s ]

The timeout (the waiting period for SIA to
switch to the next interface) is increased to
40 seconds.

[Save as Setup? ]

In addition this new value can be saved as
setup value (using the

key), before the

printer is turned ON LINE again. After this
decision turn the printer ON LINE again:
Press the

key longer than 2 seconds.

[Online ]

Note:

The printer uses SIA (Simultaneous Interface Administration) to check, which

interface is currently used for the transfer of print data.

Содержание logiJET TM4






















































































































































Результаты поиска

Содержание logiJET TM4

Отзывы:

Похожие инструкции для logiJET TM4

Бренды по названию

Популярные бренды

Microplex logiJET TM4, Руководство оператора

Результаты поиска

Содержание logiJET TM4

Отзывы:

Похожие инструкции для logiJET TM4

Бренды по названию

Популярные бренды