Microplex logiJET TM4 Скачать руководство пользователя страница 108

Страница: 108 / 149

108 Panel Functions

_______________________________________________________________________________________________

MICROPLEX

Operator’s Manual logiJET TM4

Edition 1.2p

8.3.16. Print Direction Selection

This function selects the active print orientation (orientation of the whole
printout including graphics, etc. on the paper).

Panel display

Notes

[Online ]

Turn the printer OFF LINE with this key.

[Menu Level 1 ]

. . .

Press the

key until

[Paper

] is displayed.

[Paper Menu ]

Press this key. The Paper Menu is selected.

[Paper Size ]

. . .

Press the

key until

[Print

Direct.

] is displayed.

[Print Direct. ]

Press this key. The Print Direction menu is
selected.

[Print Direct. 0 ]

The currently set print direction is displayed.

. . .

Press the

key until the

desired print direction is displayed.

[Print Direct. 1 ]

The print direction 1 = landscape is selected.

[Save as Setup? ]

In addition this new value can be saved as
setup value (using the

key), before the

printer is turned ON LINE again. After this
decision turn the printer ON LINE again:
Press the

key

longer than 2 seconds.

[Online ]

Print direction assignment: Print direction 0 = Portrait (upright format)

Print direction 1 = Landscape (horizontal format)
Print direction 2 = Portrait upside down
Print direction 3 = Landscape upside down

Содержание logiJET TM4






















































































































































Результаты поиска

Содержание logiJET TM4

Отзывы:

Бренды по названию

Популярные бренды

Microplex logiJET TM4, Руководство оператора

Результаты поиска

Содержание logiJET TM4

Отзывы:

Бренды по названию

Популярные бренды