Microplex logiJET TM4 Скачать руководство пользователя страница 103

Страница: 103 / 149

Panel Functions 103

_______________________________________________________________________________________________

MICROPLEX

Operator’s Manual logiJET TM4

Edition 1.2p

8.3.11. Hexdump Mode Activation

In the Hexdump Mode the printer prints all characters
received via interface without any interpretation (hexadecimal
coded).

This mode helps with error diagnosis. The Hexdump Mode
can be activated only temporarily.

Panel display

Notes

[Online ]

Turn the printer OFF LINE with this key.

[Menu Level 1 ]

Press this key. Menu Level 1 is selected.

[Status Sheet ]

. . .

Press the

key until

[Hexdump

] is displayed.

[Hexdump ]

The Hexdump Mode is activated.

[Hexdump ]

[Online ]

Turn the printer ON LINE again: Press the

key longer than 2 seconds. After

this the printer is ready to print again.

Note:

By activating the normal print mode (see next page) or by turning the printer

off and on again the printer can be taken out of Hexdump Mode.

Time between turning the printer off and on again should be at least

15 seconds.

Содержание logiJET TM4






















































































































































Результаты поиска

Содержание logiJET TM4

Отзывы:

Бренды по названию

Популярные бренды

Microplex logiJET TM4, Руководство оператора

Результаты поиска

Содержание logiJET TM4

Отзывы:

Бренды по названию

Популярные бренды