background image

Removing the Old Thermostat 

The original thermostats have a front cover that pops off. Behind the cover there are 2-4 mounting 

screws that must be removed to free the back plate. Once the thermostat is removed, pull out some of 
the wire from the wall to inspect how it was installed. 

Some  RV  builders  will  use  the  proper  plugs  recommended  by  the  original  thermostat 

manufacturer,  which  is  also  how  EasyTouch  RV  is  designed.  This  means  you  can  simply  unplug  the 
thermostat and proceed to the next section. 

Some  RV  builders  do  not  use  the  proper  plugs  and  direct  wire  the  thermostat  to  the  RV 

manufacturers wiring using wire crimps or similar. If the unit is direct-wired then take some pictures of 
this wiring for reference. Be sure that you can see where the thermostat wires meet with the wall wires 
as they are typically different colors. You can also write in 

Table 4

 later in the section to record what color 

wires meet.  

 

Wiring the Thermostat 

Molex™ Plugs

 

 

If your installation was done with the proper mating Molex™ plugs, then you can simply plug in 

all the mating connectors and move on to the sectio

Mounting the Thermostat

The provided wire 9-pin 

wire harness will not be needed. Not all installations will use all plugs, just ensure that every original plug 
has an EasyTouch match. 

 

If the plugs are not the standard Molex™ plugs 

that mate with EasyTouch then you will have to 

wire it direct as described in the 

Direct-Wired - General

 section. You could also make up your own plugs 

but is beyond what Micro-Air can assist with. 

 

Direct-Wired - General 

 

The  original  thermostat  will  have  wires  coming  out  of  the  back  that  are  connected  to  the  RV 

manufacturer

s wiring harness, using a crimp-splice or similar. The wire colors on the RV manufacturer

harness can vary, but the wires at the back of the original thermostat are always the same color for their 
use.  

Follow the thermostat wires to where they are spliced to the RV 

manufacturer’s 

wire harness. 

Write in the RV wiring harness colors in 

Table 4

 below before making connections. Take pictures if you 

have not already for reference as well. Some thermostats and harnesses may not have all of the wires 
shown i

Table 4

. The important part is that every original wire has an EasyTouch match. 

Содержание ASY-356-X01
























Отзывы: