METRON QA-IDS Скачать руководство пользователя страница 26

Страница: 26 / 62

The following parameters will then be displayed:

Prsr:

The pressure in the connction tube. Measurement results

display: max. value > instantaneous measured value >

mean value in mmHg.

Note:

For multiple measurements,

max. measured value > last measured value > mean

value are displayed.

Time:

The time from test start until alarm activation. Measure-

ment results display: max. time > elapsed time > mean

time in minutes/seconds.

Bolus:

The volume expansion within the tube when the infusion

pump alarm activates. Measurement results display: max.

bolus > last executed calculation after STOP is pressed >

mean bolus in milliliters.

Note:

Maximum bolus volume to

be measured with a standard QA-IDS is about 1.7

milliliters.

7. A new measurement in a series is initiated by just pressing

START (F2)

to start test.

According to the IEC an occlusion test should be run with different

settings of flow rate and, if the pump has a programmable occlusion
pressure alarm, different alarm settings are recommended.

4.4 Infusion Flow Rate

and Volume Testing

1. Press

Flow measurement (F6)

in from the Main Menu and the

display will show the

Flow Measurement Setup 1

Menu.

The following parameters are displayed:

Flow Set:

This value is the preset value of the infusion pump. All

error calculations of the flow measurement are related to

this value. If the Flow Set value is not entered correctly,

this may cause a poor presentation with incorrect overall

errors.

Press Set:

This function gives the possibility to enter + (positive) or

- (negative) backpressure into the system. Operation

range is from -200 to +600 mmHg.

dT:

Interrogation time, or time between two measurements.

Average value during the test interval is displayed. Rec-

ommended dT from IEC is 30 sec, and this is the mini-

mum value to be selected on the QA-IDS. Maximum dT

is 600 sec. or 10 minutes. Default value is 30 sec.

Содержание QA-IDS































































Результаты поиска

Содержание QA-IDS

Отзывы:

Похожие инструкции для QA-IDS

Бренды по названию

Популярные бренды

METRON QA-IDS, Руководство пользователя и обслуживания

Результаты поиска

Содержание QA-IDS

Отзывы:

Похожие инструкции для QA-IDS

Бренды по названию

Популярные бренды