Metrodata WCM-Serial Скачать руководство пользователя страница 102

Страница: 102 / 140

METRODATA LTD

WCM1100 / WCM3100 / WCM-Serial

User Manual

76-02-082 Rev J

102 of 140

5.5.2.7 Statistics

The management interface provides a full set of MIB-2 IfTable statistics for the port as
shown below:

Metrodata WCM3100 "" Alarms: Major

Interface Statistics
--------------------

ifInOctets 12451

ifInUcastPkts 0

ifInNUcastPkts 141
ifInDiscards 0

ifInErrors 0

ifInUnknownProtos 0
ifOutOctets 0

ifOutUcastPkts 0
ifOutNUcastPkts 2

ifOutDiscards 0

ifOutErrors 0

ifOutQLen 0

<Esc> - exit, <Enter> - refresh

5.5.2.8 c-VLAN

Management access to the device may be tagged or untagged with a C-VLAN tag. This
tag is supported in both C-VLAN and QinQ/S-VLAN mode of operation.

If no C-Tag is required enter 0 for None, otherwise enter the VLAN ID for the management
connection in the range 1 to 4095.

5.5.2.9 QinQ/S-VLAN

When the device is in QinQ/S-VLAN mode, the management traffic will need to be
configured with an S-Tag defined by either the Access port default tag setting, or the SVID
used on a trunk port. The valid range is 1 to 4095.

5.5.2.10 TAG 802.1p Priority

When the Manager transmits a tagged packet, C-Tag, or S-Tag this priority setting is used
as the PCP info in the tag.

The valid range is 0 to 7, with 7 being highest priority.

Содержание WCM-Serial













































































































































Результаты поиска

Содержание WCM-Serial

Отзывы:

Бренды по названию

Популярные бренды

Metrodata WCM-Serial, Руководство пользователя

Результаты поиска

Содержание WCM-Serial

Отзывы:

Бренды по названию

Популярные бренды