3-24
Revised 08.2021
Operator’s Manual: 405 SLD Seed Express
™
Bulk Seed Tender
®
®
CRUSHING HAZARD
If two people are positioning the conveyor arm;
one at the controls, the other holding the arm,
be extremely careful to prevent a crush hazard.
DO NOT place any part of your body
between stationary and moving parts.
13. When the ball coupling is free of the conveyor
hitch receiver:
- Lift the bottom of the conveyor arm over
the fender
- Hold it off the ground until it is in its final
position.
14. Use the conveyor FRONT or the conveyor
REAR buttons (switches) to position
conveyor arm into the desired position.
41
14. Use the conveyor FRONT or the conveyor
REAR buttons (switches) to position conveyor
arm into the desired position. The photos
show the self-filling position.
Fig 47 - Rotate conveyor tube
42
15. If desired, release the stand lock pin and
rotate the stand downward. Engage the lock
pin when the stand is fully extended.
16. Raise the hopper by pushing the handlebar
forward. The hopper will lock into place when
the handle has reached the end of the rail.
CAUTION
To prevent personal injury, do not use
the conveyor if the guard has been
removed.
CAUTION
Always load compartment 1 first to maintain
a positive tongue weight. Negative tongue
weight can cause the hitch to rapidly swing
upward if not securely fastened to the tow vehicle,
which can result in personal injury.
17. Start the conveyor. Refer to section 5.3 for
setting automatic seed delivery functions.
Do not open the slide gates when the
conveyor is in the self-filling position.
Fig 48 - Raise hopper canvas
15. If desired, release the stand lock pin and
rotate the stand downward. Engage the lock
pin when the stand is fully extended.
16. Raise the hopper canvas by pushing the
handlebar forward. The canvas frame will
lock into place when the handle has reached
the end of the rail.
40
10. Release and push the lock pin inward to lock
the inner and outer tubes of the conveyor arm
together. Make sure the pin is fully engaged.
MMG-00329
11. Once the tubes are locked together, rotate
hopper guide handle 90° into the position
shown.
12. Slide the ball coupling out of the conveyor
hitch receiver.
CRUSH
HAZARD
ELECTROCUTION
HAZARD
Avoid contact with overhead power
lines or electrically powered objects.
• Be aware of your surroundings when
raising or lowering conveyor.
• Maintain at least 20 feet between
equipment and any electrical hazard.
• Contact with electricity can result
in serious personal injury or death.
Keep hands and
arms clear of
conveyor tube
when placing it
in storage
position.
Weight of tube
will cause
crushing injuries.
17509
Be observant of overhead power lines or other
electrical hazards.
13. When the ball coupling is free of the conveyor
hitch receiver, lift the bottom of the conveyor
arm over the fender and hold it off the ground
until it is in its final position.
WARNING
If two people are positioning the conveyor arm,
one at the controls and the other holding the
conveyor arm, be extremely careful to prevent
a crush hazard. Do not place any part of your
body between stationary and moving parts.
Fig 46 - Moving conveyor tube
Содержание 405 SLD SEED EXPRESS
Страница 6: ...This page intentionally left blank...
Страница 20: ...2 10 Revised 08 2021 Operator s Manual 405 SLD Seed Express Bulk Seed Tender This page intentionally left blank...
Страница 68: ...5 2 Revised 08 2021 Operator s Manual 405 SLD Seed Express Bulk Seed Tender This page intentionally left blank...
Страница 72: ...6 4 Revised 08 2021 Operator s Manual 405 SLD Seed Express Bulk Seed Tender This page intentionally left blank...