Mercury SMARTCRAFT Скачать руководство пользователя страница 66

Страница: 66 / 96

SYSTEM

ACH & SPEED

3-15

SYSTEM TACH & SPEEDOMETER

Quick Cal Calibration

Quick Cal – This calibration is for setting lighting and contrast.

1. Press in the

MODE

and

TROLL

buttons for up to 2 seconds to get

to Quick Cal screen.

2. Press

MODE

to advance through the calibration selections.

CAL 1 Tachometer Calibration

Cal 1 – This calibration level lets you turn on and off the system
screens. You may configure the system to display as little or as much
information as you prefer.

1. Press in the

MODE

and

TROLL

buttons and hold for approxi-

mately 7 seconds until you see the Cal 1 screen.

2. Press

MODE

to advance through the calibration selections.

[NO]

REMOTE SCREENS?

[YES]

[SAVE]

If yes is selected, then screen changes
made on this SC1000 tach will effect
any other SC1000 tach in the system.

NOTE: all tach will need to have this screen
turned to “Yes” for this function to work.

[NO]

REMOTE LCD LIGHT?

[YES]

[SAVE]

If yes is selected, then lighting levels
made on this SC1000 tach will effect
any other SC1000 tach in the system.

NOTE: all tach will need to have this screen
turned to “Yes” for this function to work.

REMOTE LCD CONTRAST?

[YES]

[NO]

[SAVE]

If yes is selected, then contrast levels
made on this SC1000 tach will effect
any other SC1000 tach in the system.

NOTE: all tach will need to have this screen
turned to “Yes” for this function to work.

[NO]

TRIM POPUP?

[YES]

[SAVE]

Do you want power trim display screen
to pop up momentarily when you trim
the engine?

(continued on next page)

Содержание SMARTCRAFT

































































































Результаты поиска

Содержание SMARTCRAFT

Отзывы:

Похожие инструкции для SMARTCRAFT

Бренды по названию

Популярные бренды

Mercury SMARTCRAFT, Руководство по эксплуатации

Результаты поиска

Содержание SMARTCRAFT

Отзывы:

Похожие инструкции для SMARTCRAFT

Бренды по названию

Популярные бренды