Mercury SMARTCRAFT Скачать руководство пользователя страница 34

Страница: 34 / 96

MONIT

OR 2.00

2-8

MONITOR – VERSION 2.00

Standard Information Display Screens

Water Depth

Displays the depth of water un-
der the transducer if connected.

NOTE:

You must have a depth

transducer (purchased separate-
ly) connected to the system in or-
der for this screen to operate.

Shallow Water Alarm

You can set an alarm to trigger whenever the boat moves into water
shallower than the alarm level.

Setting Shallow Water Alarm.

1. The water depth screen must be displayed. Be sure Depth is

turned on in CAL 2. Refer to CAL 2 Calibration Section.

2. Press both

and

buttons together for 3 seconds.

3. The alarm on or off menu will appear.

4. Press the

button to toggle to ON.

5. Push

button to save.

6. The depth number will be flashing. Press the

button to set

the flashing number to desired alarm depth. 100 ft maximum
depth and 2 ft minimum depth.

7. Push

button to save.

Содержание SMARTCRAFT

































































































Результаты поиска

Содержание SMARTCRAFT

Отзывы:

Похожие инструкции для SMARTCRAFT

Бренды по названию

Популярные бренды

Mercury SMARTCRAFT, Руководство по эксплуатации

Результаты поиска

Содержание SMARTCRAFT

Отзывы:

Похожие инструкции для SMARTCRAFT

Бренды по названию

Популярные бренды