Mercury SMARTCRAFT Скачать руководство пользователя страница 60

Страница: 60 / 96

SYSTEM

ACH & SPEED

3-9

SYSTEM TACH & SPEEDOMETER

TROLL

–

TROLL

–

Speedometer

Tachometer

Actual Speed

Set Speed

Actual Speed

Set Speed

Troll Control

To Set Troll Control

1. With the engine running, shift engine into gear. Set engine speed

at idle.

2. Push in the

TROLL

–

button to bring up the troll control dis-

play screen.

3. Press

MODE

to engage (turn on) the troll control.

4. Use the

TROLL

–

buttons to set the desired speed. Use (+)

to increase speed and (–) to decrease speed.

5. If you set troll control to a higher speed than the troll rpm can bring

the boat to, the TARGET SPEED TOO FAST (a) message will ap-
pear. Reduce troll speed.

6. If you set troll control to a slower speed than the troll rpm can bring

the boat to, the TARGET SPEED TOO SLOW (b) message will ap-
pear. Increase troll speed.

To Get Out of Troll Control

There are three ways to turn off the troll control:

•

Press the

MODE

button when in the troll display screen.

•

Move the throttle to a different speed.

•

Shift engine into neutral.

Содержание SMARTCRAFT

































































































Результаты поиска

Содержание SMARTCRAFT

Отзывы:

Бренды по названию

Популярные бренды

Mercury SMARTCRAFT, Руководство по эксплуатации

Результаты поиска

Содержание SMARTCRAFT

Отзывы:

Бренды по названию

Популярные бренды