Mercury SMARTCRAFT Скачать руководство пользователя страница 84

Страница: 84 / 96

SMAR

ACH & SPEED

4-7

SMART TACH & SPEEDOMETER

gog95

TROLL

–

TROLL

–

Speedometer

Tachometer

Actual Speed

Set Speed

Actual Speed

Set Speed

osl7

Troll Control

To Set Troll Control

1. With the engine running, shift outboard into gear. Set engine

speed at idle.

2. Push in the

TROLL

–

button to bring up the troll control

display screen.

3. Press

MODE

to engage (turn on) the troll control.

4. Use the

TROLL

–

buttons to set the desired speed. Use (+)

to increase speed and (–) to decrease speed.

5. If you set troll control to a higher speed than the troll rpm can

bring the boat to, the TARGET SPEED TOO FAST (a) message
will appear. Reduce troll speed.

6. If you set troll control to a slower speed than the troll rpm can

bring the boat to, the TARGET SPEED TOO SLOW (b) message
will appear. Increase troll speed.

To Get Out of Troll Control

There are three ways to turn off the troll control:

•

Press the

MODE

button when in the troll display screen.

•

Move the throttle to a different speed.

•

Shift outboard into neutral.

Содержание SMARTCRAFT

































































































Результаты поиска

Содержание SMARTCRAFT

Отзывы:

Бренды по названию

Популярные бренды

Mercury SMARTCRAFT, Руководство по эксплуатации

Результаты поиска

Содержание SMARTCRAFT

Отзывы:

Бренды по названию

Популярные бренды