manualshive.com logo in svg

Mercury SMARTCRAFT, Руководство по эксплуатации

Поделиться
Скачать
Mercury SMARTCRAFT Скачать руководство пользователя страница 90

SMAR

T

 T

ACH & SPEED

4-13

SMART TACH & SPEEDOMETER

osl17

Tachometer Calibration

CALIBRATION

[DOWN]

CONTROL OPTIONS

[UP]

[SAVE]

TRIM POP UP  ?  YES – NO

Do you want power trim angle display
screen to pop up whenever you trim
the outboard ? Press + or – to select.
Press MODE to save.

CALIBRATION

[DOWN]

ENGINE POSITION

[UP]

[SAVE]

SINGLE-PORT-CENTER-STARBOARD

Match tachometer to the correct en-
gine. Press + to select engine. Press
MODE to save.

[DOWN]

[UP]

[SAVE]

CALIBRATION

DISPLAY UNITS

ENGLISH - METRIC

Select display readings in English or
Metric. Press + or – to select Press
MODE to save.

CALIBRATION

SPEED UNITS

KN - KPH - MPH

[DOWN]

[UP]

[SAVE]

Display boat speed in KN (knots),
KPH (kilometers per hour), MPH
(miles per hour). Press + or – to se-
lect setting. Press MODE to save.

CALIBRATION

EXTERNAL SENSORS

[EDIT]

[SKIP]

CALIBRATION

SPEEDO SENSOR ?  YES/NO

EXTERNAL SENSORS

[DOWN]

[UP]

[SAVE]

CALIBRATION

PADDLE WHEEL SENSOR ?  YES/NO

EXTERNAL SENSORS

[DOWN]

[UP]

[SAVE]

CALIBRATION

WATER TEMP SENSOR ?  YES/NO

EXTERNAL SENSORS

[DOWN]

[UP]

[SAVE]

Press MODE to skip to the next dis-
play. Press + (edit) if your adding or
deleting any external sensor to the
SmartCraft System.
Editing External Sensors
Chose Yes or No for each sensor
No = not used  Yes = in use
Press + or – for correct setting 
Press MODE to save and advance to
next sensor

(continued on next page)

Содержание SMARTCRAFT

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды