Mercury SMARTCRAFT Скачать руководство пользователя страница 94

Страница: 94 / 96

SMAR

ACH & SPEED

4-17

SMART TACH & SPEEDOMETER

osl27

Speedometer Calibration

Simple Calibration – This calibration for setting lighting and setting
the clock can be made while engine is running.

1. Press in the

MODE

and

TROLL

buttons for calibration screen.

2. Press

MODE

to advance through the calibration selections.

Advanced Calibration – This calibration goes through the entire
mode selections.

1. Turn ignition key to the off position.

2. Hold

TROLL

–

and turn ignition key to the on position.

3. Press and hold

MODE

for 2 seconds to bring up the calibration

screen.

4. Press

MODE

to advance through the calibration selections.

[DOWN]

CALIBRATION

BRIGHTNESS

[UP]

[SAVE]

Press – or + to adjust level. Press
MODE to save setting

CALIBRATION

BRIGHTNESS

[ YES ]

[ NO ]

SET ALL INSTRUMENTS?

Do you want the same brightness lev-
el for all SmartCraft gauges? Press +
for yes. Press MODE for no.

[DOWN]

CALIBRATION

[UP]

[SAVE]

CONTRAST

Press – or + to adjust level. Press
MODE to save setting

CONTRAST

CALIBRATION

[ YES ]

[ NO ]

SET ALL INSTRUMENTS?

Do you want the same contrast level
for all SmartCraft gauges? Press + for
yes. Press MODE for no.

(continued on next page)

Содержание SMARTCRAFT

































































































Результаты поиска

Содержание SMARTCRAFT

Отзывы:

Похожие инструкции для SMARTCRAFT

Бренды по названию

Популярные бренды

Mercury SMARTCRAFT, Руководство по эксплуатации

Результаты поиска

Содержание SMARTCRAFT

Отзывы:

Похожие инструкции для SMARTCRAFT

Бренды по названию

Популярные бренды