Mercury 92-858058K01 страница 71 Скачать руководство пользователя

Страница: 71 / 150

Section 3 - On the Water

90-879172181

eng

FEBRUARY 2011

Page 63

1. Press the "TURN" button in the direction of the desired heading change. Each press of the button changes the desired heading

by 10°.

a -

Port "TURN" button

b -

Starboard "TURN" button

2. Move (press) the joystick in the desired direction to make small adjustments in the chosen heading. Each recognized

movement adjusts the chosen heading by 1°.

NOTE: The joystick must move over 50% of its travel for the movement to be recognized as input.

24707

Adjusting heading to starboard

To Resume a Heading

The "RESUME" button light is on if the previous course heading is available to resume.
IMPORTANT: The previous heading can only be resumed within four minutes of Auto Heading being disengaged or if the boat

has not turned more than 45°.
Press the "RESUME" button to resume the previous heading if you:
•

Turned the steering wheel and disengaged Auto Heading.

27699

Содержание 92-858058K01























































































































































Результаты поиска

Содержание 92-858058K01

Отзывы:

Похожие инструкции для 92-858058K01

Бренды по названию

Популярные бренды

Mercury 92-858058K01, Руководство пользователя

Результаты поиска

Содержание 92-858058K01

Отзывы:

Похожие инструкции для 92-858058K01

Бренды по названию

Популярные бренды