manualshive.com logo in svg

Mercury 92-858058K01, Руководство пользователя, Страница: 25 / 150

Поделиться
Скачать
Mercury 92-858058K01 Скачать руководство пользователя страница 25

Section 2 - Getting to Know Your Power Package

90-879172181   

eng

  FEBRUARY  2011

Page  17

4. Remove the three M5 screws securing the side cover.

41347

Location of side cover screws

5. Remove the side cover.
6. For adjustment, temporarily install the handle, washer and screw. Finger‑tighten the screw.
7. To adjust the ERC handle detent tension:

a. Turn the adjustment screw clockwise to increase tension on the control handle and counter‑clockwise to decrease

tension.

b. Adjust to the desired tension.

8. To adjust ERC handle tension:

a. Turn the adjustment screw clockwise to increase tension on the control handle and counter‑clockwise to decrease

tension.

b. Adjust to the desired tension.

Side cover removed

a -

Detent tension adjustment screw

b -

Handle tension adjustment screw

9. Remove the screw, washer, and handle when the adjustments are complete.
10. Install the side cover. Secure the cover with the three M5 x 10 mm long screws. Tighten the screws to specification.

Description

Nm

lb‑in.

lb‑ft

Side cover screws

3.4

30

–

11. Apply adhesive to the threads of the handle screw.

Tube Ref No.

Description

Where Used

Part No.

7

Loctite 271 Threadlocker

Threads of handle screw

92-809819

a

b

41340

Содержание 92-858058K01























































































































































Отзывы:

Нет отзывов