Mercury 92-858058K01 Скачать руководство пользователя страница 103 | Manualshive

Страница: 103 / 150

Mercury 92-858058K01 Скачать руководство пользователя страница 103

Section 5 - Maintenance

90-879172181

eng

FEBRUARY 2011

Page 95

2. Remove the dipstick. Wipe the dipstick with a clean, lint‑free cloth.

37829

Transmission dipstick, with cover removed for clarity

3. Insert the dipstick, resting it on the top of the threaded hole.
4. Remove the dipstick and check the oil level indicated. The oil level should be between the maximum and minimum marks on

the dipstick.

NOTE: Oil from the transmission oil cooler and hoses may drain into the transmission, causing an oil level slightly above the

maximum mark.

Checking—dipstick resting on top of threaded hole

a -

Maximum mark

b -

Minimum mark

c -

Top of threaded hole

d -

Dipstick

5. If the level is correct, install the dipstick.
6. If the level is low, add the specified transmission oil through the dipstick threaded hole to bring the level up to the maximum

mark on the dipstick.

Description

Fluid Type

Fluid Part Number

Transmission and drop box

Synthetic Power Steering Fluid SAE

0W‑30

92‑858077K01

NOTE: If the transmission oil level is extremely low, contact your local Cummins MerCruiser Diesel Authorized Repair Facility.

IMPORTANT: For a more accurate measurement, operate the engine at 1500 RPM for three minutes immediately before

checking the oil level.

NOTICE

The seawater pumps on vessels equipped with Zeus pod drives can be damaged by excessive exhaust aeration due to

inadequate water flow. To ensure adequate water flow across the seawater inlets, make sure that the vessel is underway before

exceeding 1500 RPM.

7. Start the engine and operate at 1500 RPM for three minutes to fill all the hydraulic circuits. To avoid excessive exhaust aeration

of the seawater, do not operate the engine above 1500 RPM.

8. Stop the engine and quickly check the oil level.
9. If the oil level is low, add the specified transmission oil to bring the level up to the maximum mark on the dipstick.
10. Install the dipstick.
11. Install the drive cover if it was removed. Refer to

Installing the Drive Cover.

12. If your model is equipped with a drive cover, install the access cover.

28080

d

c

a

b

«
...
101
102
103
104
105
...
»

Содержание 92-858058K01























































































































































Отзывы:

Нет отзывов