MerCruiser Sterndrive 350 MAG MPI Скачать руководство пользователя страница 57

Страница: 57 / 148

Section 3 - On The Water

90-864195061 NOVEMBER 2006

Page 49

CAUTION

Shifting the drive system at RPMs greater than engine idle speed may cause internal

damage to the drive system. Shift the drive system only when the engine is at idle RPM.

STOPPING THE ENGINE

1. Move the remote control handle to neutral/idle and allow the engine to slow to idle

speed. If engine has been operated at high speed for a long period of time, allow the

engine to cool at idle speed for 3 to 5 minutes.

2. The engine can be stopped by any one of the following 4 methods:

Move the ignition key switch to the "ACCESSORY" or "OFF" position. The engine

will stop and the control system will be deactivated.

Depress the start/stop button, if equipped. The engine will stop and the control

system will remain active.

Momentarily move the ignition key switch to the "START" position, then release

immediately. The control system will recognize that the engine is running and will

stop the engine. The control system will remain active. Moving the ignition key

switch to the "START" position again will issue a start request to the control system

and the control system will start the engine, if appropriate.

Activate the lanyard stop switch, if equipped. The engine will stop, but the control

system will remain active. The control system will not allow the engine to start if

the lanyard stop switch is activated.

Throttle Only Operation

NOTE: When operating in throttle only (neutral) mode, the DTS Control System will not

allow the engine speed to increase above 3500 RPM.

Zero effort remote controls:

Zero effort remote controls have seperate throttle control

and shift control levers. Advancing the throttle control lever beyond the idle position while

the shift control lever is in the neutral position will cause engine speed to increase, but only

up to the maximum neutral engine speed of 3500 RPM.

WARNING

The Digital Throttle and Shift (DTS) Zero Effort control can shift the engine or

transmission at speeds greater than idle, causing unexpected boat movement, which

may result in injury, death, or property damage due to loss of boat control. Always place

the throttle control lever in the idle position before moving the shift control lever into

forward or reverse gear position.

Panel Mount and Console Mount Remote Controls:

Panel mount and console mount

remote controls are equipped with a throttle only button. To activate throttle only mode:
1. Refer to

Remote Controls

section for remote control features.

2. Move the control lever to the idle/neutral position.
3. Depress the throttle only button, and move the control lever to the idle/forward or idle/

reverse position. The DTS control system will sound two beeps on the audio warning

horn to indicate throttle only mode is active. On console mount remote controls, the

neutral light will begin to blink.

4. Advancing the control lever beyond the idle/forward or idle/reverse position will cause

engine speed to increase.

IMPORTANT: Moving the control lever back to the idle/neutral position will deactivate the

throttle only mode and allow the engine to shift into gear.

Содержание Sterndrive 350 MAG MPI





















































































































































Результаты поиска

Содержание Sterndrive 350 MAG MPI

Отзывы:

Похожие инструкции для Sterndrive 350 MAG MPI

Бренды по названию

Популярные бренды

MerCruiser Sterndrive 350 MAG MPI, Руководство пользователя

Результаты поиска

Содержание Sterndrive 350 MAG MPI

Отзывы:

Похожие инструкции для Sterndrive 350 MAG MPI

Бренды по названию

Популярные бренды