MerCruiser Sterndrive 350 MAG MPI Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 148

background image

Section 3 - On The Water

Page 46

90-864195061 NOVEMBER 2006

b.

Turn ignition key to "START". Release key when engine starts and allow switch

to return to "ON" position.

5. If engine does not start after step 4:

a.

Move the remote control handle/throttle lever to full throttle position, then return

to 1/4 throttle.

b.

Turn ignition key to "START". Release key when engine starts and allow switch

to return to "ON" position.

6. Inspect the power package for fuel, oil, water and exhaust leaks.
7. Move control handle with a firm, quick motion forward to shift to forward gear, or

backward to shift to reverse. After shifting, advance throttle to desired setting.

!

CAUTION

Shifting the drive system at RPMs greater than engine idle speed may cause internal

damage to the drive system. Shift the drive system only when the engine is at idle RPM.

STOPPING THE ENGINE

1. Move the remote control handle to neutral/idle and allow the engine to slow to idle

speed. If engine has been operated at high speed for a long period of time, allow the

engine to cool at idle speed for 3 to 5 minutes.

2. Turn ignition key to the "OFF" position.

Starting Engine After Stopped While In Gear

IMPORTANT: Avoid stopping the engine if the sterndrive unit is in gear. If the engine does

stop, refer to the following procedure:
1. Push and pull repeatedly on the remote control handle until handle returns to the

neutral/idle position. This may take several tries if the power package was operating

above idle RPM when the engine stopped.

2. After the handle returns to the neutral/idle position, resume normal starting procedures.

Throttle Only Operation

1. Refer to

Remote Controls

section for remote control features.

2. Move the control lever to the idle/neutral position.
3. Depress and hold the throttle only button, and move the control lever to the idle/forward

or idle/reverse position.

4. Advancing the control lever beyond the idle/forward or idle/reverse position will cause

engine speed to increase.

IMPORTANT: Moving the control lever back to the idle/neutral position will disengage the

throttle only button and allow the engine to shift into gear.
5. Throttle only mode is deactivated by moving the control lever to the idle/neutral position.

Moving the control lever from the idle/neutral position to the idle/forward or idle/reverse

position without pressing the throttle only button will shift the unit into the chosen gear.

Trailering the Boat

Your boat can be trailered with the sterndrive unit in the up or down position. Adequate

clearance is required between the road and sterndrive when transporting.
If adequate road clearance is a problem, place the sterndrive unit in full trailer position and

support it with an optional trailer kit which is available from your authorized Mercury

MerCruiser dealer.

«
...
52
53
54
55
56
...
»

Содержание Sterndrive 350 MAG MPI





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sterndrive 350 MAG MPI

Бренд: Admiral Страницы: 9

PRESTIGE PS2.60FA

Бренд: CAB Страницы: 16

Бренд: 3W Страницы: 20

Бренд: Great Wall Страницы: 72

Бренд: Hitachi Страницы: 41

Бренд: Hitachi Страницы: 1037

Бренд: Hitachi Страницы: 1104

Бренд: Siemens Страницы: 28

6FB1203-5AT00-7MP0

Бренд: Siemens Страницы: 7

COMBIMASTER CM110/3

Бренд: Siemens Страницы: 21

Бренд: Siemens Страницы: 19

Бренд: Siemens Страницы: 24

Бренд: Siemens Страницы: 15

Бренд: Siemens Страницы: 16

Бренд: Siemens Страницы: 38

Бренд: Siemens Страницы: 24

Бренд: Siemens Страницы: 36

Бренд: Siemens Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды