MerCruiser Sterndrive 350 MAG MPI Скачать руководство пользователя страница 38

Страница: 38 / 148

Section 2 - Getting to Know Your Power Package

Page 30

90-864195061 NOVEMBER 2006

Slim Binnacle Console Mount Features ‑ Single Engine

START

STOP

14637

a -

Control handle

b -

Trim/tilt switch

c -

Active light

d -

Neutral light

e -

Start/stop button

f -

Throttle only/station select key

g -

Detent tension adjustment

h -

Control handle friction adjustment screw

Control Handle -

Operation of the shift and throttle are controlled by the movement of the

control handle. Push the control handle forward from neutral with a quick, firm motion to

the first detent for forward gear. Continue pushing forward to increase speed. Pull the

control handle back from neutral with a quick, firm motion to the first detent for reverse gear

and continue pushing back to increase speed.

Trim/Tilt Switch (if equipped) -

Refer to

Power Trim

Active Light -

The active light is illuminated to show the remote control is active and ready

for use.

Neutral Light -

The neutral light is illuminated when the engine is in neutral gear position.

NOTE: Gear position is determined by sensing the position of the shift actuator on the

engine, not the position of the gear switch.

Stop/Start Button -

Allows the boat operator to start or stop the engine without using the

ignition key.

Throttle Only/Station Select Key -

Allows engine throttle advancement without shifting

the engine. The throttle only/station select button also allows the boat operator to select

which remote control is in control of the engine operation when operating with multiple

helms. Refer to

Dual Helm Station Transfer

Detent Tension Adjustment Screw -

This screw can be adjusted to increase or decrease

the effort required to move the control handle out of the detent positions (cover must be

removed). Turning the screw clockwise will increase tension.

Control Handle Friction Adjustment Screw -

This screw can be adjusted to increase or

decrease the tension on the control handle (cover must be removed). This will help prevent

unwanted motion of the handle in rough water. Turn the screw clockwise to increase

tension and counterclockwise to decrease tension.

Содержание Sterndrive 350 MAG MPI





















































































































































Результаты поиска

Содержание Sterndrive 350 MAG MPI

Отзывы:

Похожие инструкции для Sterndrive 350 MAG MPI

Бренды по названию

Популярные бренды

MerCruiser Sterndrive 350 MAG MPI, Руководство пользователя

Результаты поиска

Содержание Sterndrive 350 MAG MPI

Отзывы:

Похожие инструкции для Sterndrive 350 MAG MPI

Бренды по названию

Популярные бренды