MerCruiser Sterndrive 350 MAG MPI Скачать руководство пользователя страница 122

Страница: 122 / 148

Section 6 - Storage

Page 114

90-864195061 NOVEMBER 2006

Cold Weather or Extended Storage

IMPORTANT: Mercury MerCruiser strongly recommends that this service should be

performed by an authorized Mercury MerCruiser dealer. Damage caused by freezing

temperatures IS NOT covered by the Mercury MerCruiser Limited Warranty.

CAUTION

Seawater that is trapped in or remains in the cooling system seawater section during cold

weather or winter storage can freeze resulting in cooling system or engine damage.

Completely drain the seawater from the cooling system seawater section for winter

storage or immediately after cold weather operation when the possibility of freezing

temperatures exist.

IMPORTANT: Mercury MerCruiser requires that propylene glycol antifreeze, mixed to the

manufacturers instructions, be used in the seawater section of the cooling system for

freezing temperatures or extended storage. Make sure that the propylene glycol antifreeze

contains a rust inhibitor and is recommended for use in marine engines. Be certain to follow

the propylene glycol manufacturer's recommendations.

Preparing Power Package for Storage

1. Fill the fuel tanks with fresh gasoline (that does not contain alcohol) and a sufficient

amount of Quicksilver Gasoline Stabilizer for Marine Engines to treat the gasoline.

Follow instructions on the container.

2. If the boat is to be placed in storage with fuel containing alcohol in fuel tanks (if fuel

without alcohol is not available): Fuel tanks should be drained as low as possible and

Mercury/Quicksilver Gasoline Stabilizer for Marine Engines added to any fuel

remaining in the tank. Refer to

Fuel Requirements

for additional information.

3. Flush the cooling system. Refer to the

Maintenance

section.

4. For additional assurance against freezing and rust, after draining, fill the seawater

cooling system with propylene glycol mixed to the manufacturer's recommendation to

protect engine to the lowest temperature to which it will be exposed during freezing

temperatures or extended storage.

5. Operate the engine sufficiently to bring it up to normal operating temperature and allow

fuel with Mercury/Quicksilver Gasoline Stabilizer to circulate through the fuel system.

Shut off the engine.

6. Change the oil and oil filter.
7. Prepare the engine and fuel system for storage. Refer to

Engine and Fuel System

Preparation

. Perform this operation.

8. Drain the engine seawater cooling system. Refer to

Draining the Seawater System

CAUTION

If the boat is in the water, the seacock must remain closed until the engine is to be

restarted to prevent water from flowing back into the cooling system or the boat. If the

boat is not fitted with a seacock, leave the water inlet hose disconnected and plugged to

prevent water from flowing back into the cooling system or the boat. As a precautionary

measure, attach a tag to the ignition switch or steering wheel of the boat with the warning:

Open the seacock or reconnect the water inlet hose before starting the engine.

9. Store the battery according to the manufacturer's instructions.

Содержание Sterndrive 350 MAG MPI





















































































































































Результаты поиска

Содержание Sterndrive 350 MAG MPI

Отзывы:

Похожие инструкции для Sterndrive 350 MAG MPI

Бренды по названию

Популярные бренды

MerCruiser Sterndrive 350 MAG MPI, Руководство пользователя

Результаты поиска

Содержание Sterndrive 350 MAG MPI

Отзывы:

Похожие инструкции для Sterndrive 350 MAG MPI

Бренды по названию

Популярные бренды