Mercedes-Benz Comand MY11 Скачать руководство пользователя

Страница: 13 / 194

radiate radio frequency energy and, if not

installed and used in accordance with the

instruction manual, may cause harmful

interference to radio communications.

WARNING

This equipment complies with FCC radiation

exposure limits set forth for uncontrolled

equipment and meets the FCC radio

frequency (RF) Exposure Guidelines in

Supplement C to OET65.
This equipment has very low levels of RF

energy that is deemed to comply without

maximum permissive exposure evaluation

(MPE). But it is desirable that it should be

installed and operated with at least 8inches

(20cm) and more between the radiator and a

person's body (excluding extremities: hands,

wrists, feet and legs.)

Correct use

Observe the following information when using

COMAND:

the safety notes in this manual

all road traffic regulations

Improper work on electronic components

or other systems (such as radio, DVD

changer) and their software may result in

malfunction or failure. Even systems that

have not been modified could be affected

because the electronic systems are

connected. Electronic malfunctions can

seriously jeopardize the operational safety

of your vehicle.

Only have repairs or changes to electronic

components carried out at a qualified

specialist workshop which has the

necessary specialist knowledge and tools

to carry out the work required. Daimler

recommends that you use an authorized

Mercedes-Benz Center for this purpose. In

particular, work relevant to safety or on

safety-related systems must be carried out

at a qualified specialist workshop.

Protection against theft: this device is

equipped with technical provisions to

protect it against theft. Further information

on protection against theft can be obtained

from an authorized Mercedes-Benz Center.

Information on copyright

Macrovision™

This product incorporates copyright

protection technology that is protected by

U.S. patents and other intellectual property

rights. Use of this copyright protection

technology must be authorized by Rovi

Corporation, and is intended for home and

other limited viewing uses only unless

otherwise authorized by Rovi Corporation.

Reverse engineering or disassembly is

prohibited.

Free Type

Components of this software are subject to

2005 The FreeType Project

http://www.freetype.org.
All rights reserved.

Vehicle equipment

These Operating Instructions describe all

standard and optional equipment available

for your COMAND system at the time of

purchase. Country-specific deviations are

possible. Please note that your COMAND

system may not be equipped with all the

features described. This includes safety-

related systems and functions. Therefore, the

equipment on your COMAND system may

differ from that in the descriptions and

illustrations. The original purchase

agreement lists all systems installed in your

vehicle. Contact an authorized Mercedes-

Benz Center if you have any questions about

equipment or operation.

Introduction

Содержание Comand MY11



































































































































































































Результаты поиска

Содержание Comand MY11

Отзывы:

Похожие инструкции для Comand MY11

Бренды по названию

Популярные бренды

Mercedes-Benz Comand MY11, Руководство по эксплуатации

Результаты поиска

Содержание Comand MY11

Отзывы:

Похожие инструкции для Comand MY11

Бренды по названию

Популярные бренды